* RD-102, AQUARIUM REEF RO DI REVERSE OSMOSIS WATER FILTRATION SYSTEM, NO TANK NO FAUCET
Overall rejection/removal rate:
99 to 100%
1st stage: 5 micron sediment filter, removes sediment, rust, dirt. (replace every
2nd & 3rd stage: premium grade coconut shell carbon block filter, removes chlorine,
chloramines, bad taste and odor (replace every 6-12 month)
4th stage high rejection TFC-100GPD membrane, removes 95% to 97% of chemical,
minerals, dissolved solids, like arsenic, lead, silica, nitrate, copper, ammonia,
sodium, fluoride, etc. (replace every 2 to 3 years)
5th & 6th stage: de-ionized filter, further removes the mineral and chemical contents
of water and achieving 99% to 100% removal rate (replace as needed, or after 600
to 1000 gallons). It comes with refillable clear casing. The DI resin inside changes
color from green to dark brown when the resin is exhausted.
*Feed water pressure: 40-80 psi, (for pressure below 40 psi, use booster pump
or permeate pump)
*Feed water temperature: 40-100 F
*pH range: 3-10 *Hardness: lower than 500ppm (hard water will shorten the life
of filters, but system will still perform) Using a water softening system prior
to RO+DI filter will prolong the life of filters.
*Dissolved iron: less than 1 ppm
*Total Dissolved Solids (TDS): less than 1000 ppm, higher TDS will shorten the
life of filters.
* Dimension: 15in width x 16in height x 5.5in depth
* The system come with under-the-sink adapter, drain clamp, tubing, shut off valve.
Optional easy-connect adapters are available for countertop installation or garden hose/ laundry room installation..
FREE bonus Pressure Gauge: It's helpful in monitoring:
- House water pressure
- Operating pressure of the RO system
- When to replace sediment & carbon filters
- When troubleshooting the system
|2DI Filters: Clear, refillable housing
The DI resin we used is the highest grade, nuclear grade mixed-bed resin. It is used in pharmaceuticals, semiconductors, laboratory applications. It is able to achieve the highest purity of 0 ppm (Zero mineral, Zero Silica) and near 18 meg.ohm resistivity. Now it is available to Aquarium lover and reefer at affordable prices.
|DI Filter Dispensing Ball Valve is included: We specially include additional ball valve for the DI filter. The output is going to your own container or fish tank. When you shut-off this valve at the output, the automatic shut off valve with turn off the system in about 1 to 2 minutes. You don't need to shut off at the water supply. Just shut off the output valve, system would shut off
|Automatic-Shut-Off Valve is included; when you shut off the dispensing valve or when your own float valve closes, the automatic shut-off valve shuts off the water feed and drain, preventing wastage of water going to drain. And if you have your own large container and float control valve, this system would turn ON/OFF automatically to refill your container.
|Feed Water Adapter: for under the sink installation, we give you the adapter with valve to put in between the cold water line. Our adapter has several advantages over the self-piercing valve. Our adapter will not clog up like the needle point piercing valve. also our adapter does not require putting a hole in the pipe. also you can easily replace the valve or relocate the valve without changing your piping, unlike the other self-piercing valve, where once it punctures a hole you cannot replace the valve, then you need to replace the pipe and the valve.
|Clear bottom 3 filter housings:
For easy checking of filter condition
We use a
fixed rate flow restrictor to accurately restrict the drain line and create
proper working pressure for the operation of the reverse osmosis
process. Therefore, a more efficient and favorable pure water to drain ratio is
achieved at 1:3
NOTE: We have abandoned the type of flow restrictor that has a black
lever on top for flushing since it is not an accurate flow restrictor.
Optional Manual flush valve:
system flushes itself when it is making water. In most cases a manual flush
valve is not required. However, it is beneficial to manually flush the membrane
if the water supply is from well or very hard water, above 600 ppm of TDS or
Hardness. Optional manual flush valve requires additional fee.